surface mount superfast rectifi er voltage - 50 to 600 volts current - 2.0 ampere features ? for surface mounted applications ? low profile package ? built-in strain relief ? easy pick and place ? superfast recovery times for high efficiency ? plastic package has underwriters laboratory flammability classification 94v-o ? glass passivated junction ? high temperature soldering: 260 / 10 seconds at terminals high temperature soldering : 260 ? o c / 10 seconds at terminals pb free prod ? uct at available : 99% sn above meet rohs environment substance directive request mechanical data ? case: jedec do-214aa molded plastic ? terminals: solder plated, solderable per mil-std-750, method 2026 ? polarity: indicated by cathode band ? standard packaging: 12mm tape (eia-481) ? weight: 0.003 ounce, 0.093 gram maximum ratings and electrical characteristics ratings at 25 j ambient temperature unless otherwise specified. single phase, half wave, 60hz, resistive or inductive load. for capacitive load, derate current by 20%. symbols ER2A er2b er2c er2d er2e er2g er2j units maximum recurrent peak reverse v oltage vrrm 50 100 150 200 300 400 600 volts maximum rms voltage vrms 35 70 105 140 210 280 420 volts maximum dc blo cking voltage vdc 50 100 150 200 300 400 600 volts maximum average forward rectif ied current , at tl=110 i(av) 2.0 amps peak forward surge current 8.3ms single half si newave superi mposed on rated load(jedec method) ifsm 50.0 amps maximum instantaneous forward vol tage at 2.0a vf 0.95 1.25 1.7 volts maxi mum dc reverse cur rent t a=25 at rated dc blocking voltage ta=100 ir 5.0 100 ua maximum reverse recovery time (note 1) trr 35.0 ns typi cal junction capacitance (note 2) cj 25.0 pf typical thermal resistance (note 3 ) 20.0 /w operating and storage temperature range tj,tstg -55 to +150 notes: 1. reverse recovery test conditions: if=0.5a, ir=1.0a, irr=0.25a 2. measured at 1 mhz and applied reverse voltage of 4.0 volts 3. 8.0mm2 (.013mm thick) land areas .083(2.11) .075(1.91) .012(.305) .006(.152) .012(.31) .006(.15) .008(.203) .002(.051) .050(1.27) .030(0.76) smb/do-214aa unit:inch(mm) .155(3.94) .130(3.30) .185(4.70) .160(4.06) . 096(2.44) .0 83(2.13) .220(5.59) .200(5.08) r ja o c o c data sheet ER2A~er2j semiconductor http://www.yeashin.com 1 rev.02 20110725 c c c c c
ratings and characteristic curves note:1.rise time = 7ns max. in p ut im p edance = 1 me g ohm. 22 p f 2.rise time = 10ns max. source im p edance = 50 ohms t rr +0.5a 0 -0.25 -1.0 set time 1cm base for 50 ns/cm 2.4 2.0 1.6 1.2 0.8 0.4 0 0 20 40 60 80 100 120 140 160 single phase half wave 60hz resistive or inductive load p.c.b. mounted on 0.30.3"(8.08.0mm) copper pad areas lead temperature , fig. 1-reverse recovery time characteristic and test circuit diagram fig. 2-maximum average forward current rating 0 20 40 60 80 100 120 140 1,000 100 10 1 0.1 0.01 t j = 100 t j = 75 t j = 25 percent of rated peak inverse voltage, volts 50.0 10.0 1.0 0.1 0.01 0.4 0.5 0.8 1.0 1.2 1.4 1.6 1.8 ER2A er2e er2j tj = 25 pulse width = 300 2% duty cycle reverse voltage, volts fig. 3-typical reverse characteristics fig. 4-typical forward characteristics 60 50 40 30 20 10 1 2 5 10 20 50 100 8.3ms single half sine wave jedec method number of cycles at 60hz 60 50 40 30 20 10 .1 .5 1 2 5 10 20 50 100 200 500 1000 tj = 25 f = 1.0mhz vsig = 50mvp-p reverse voltage, volts fig. 5-maximum non-repetitive peak forward surge current fig. 6-typical junction capacitance peak forward surge current, amperes instantaneous reverse current, microamperes capacitance, pf instantaneous forward current amperes average forward rectified current, amperes ER2A~er2j http://www.yeashin.com 2 rev.02 20110725 c c c c c c ns
|
